Help needed: Arduino Wireless Notice Board project

salmanfaris

@SAFVAN what was the solution with the previous problem?

rafitc99

@salmanfaris tried @arunksoman suggestion , c_str() instead to_charArray().. But want to parse SMS body only. Now working on that.

codelery

@rafitc99 what is the final code? Could you please share it with us? I have been battling with a similar project.

Which Arduino board did you use?

thanks

rafitc99

@codelery You can use any Arduino board. So far as i remember, we used Arduino UNO.

Somehow i found the code in my gist. It was a 3 year old project. So, i don't remember most of the things

Code:

#include <SoftwareSerial.h>
#include <SPI.h>
#include <DMD.h>
#include <TimerOne.h>
#include "SystemFont5x7.h"
#include "Arial_black_16.h"

#define ROW 1
#define COLUMN 1
#define FONT Arial_Black_16

DMD led_module(ROW, COLUMN);

String st;
const char *msg;
unsigned int LengMsg;
char finalMsg[100] = "";
SoftwareSerial mySerial(3, 2);

void scan_module() {
  led_module.scanDisplayBySPI();
}

void setup() {
  Timer1.initialize(2000);
  Timer1.attachInterrupt(scan_module);
  led_module.clearScreen( true );

  Serial.begin(9600);
  mySerial.begin(9600);
  Serial.println("Starting...");
  delay(1000);
  mySerial.println("AT");
  updateSerial();
  mySerial.println("AT+CMGF=1");
  updateSerial();
  mySerial.println("AT+CNMI=1,2,0,0,0");
  updateSerial();
}

void loop() {
  //  pollSms();
  displayMessage();
  delay(500);

  //Start print in led matrix
  led_module.selectFont(FONT);
  led_module.drawMarquee(finalMsg, LengMsg, (32 * ROW), 0);
  long start = millis();
  long timming = start;
  boolean flag = false;
  while (!flag) {
    if ((timming + 20) < millis()) {
      flag = led_module.stepMarquee(-1, 0);
      timming = millis();
    }
  }
}

//------GSM Helper

void displayMessage()
{
  delay(500);
  String msg = "";
  int start = 0, endPoint = 0;
  finalMsg[100] = "";
  while (Serial.available())
  {
    mySerial.write(Serial.read());//Forward what Serial received to Software Serial Port
    //     parseData(mySerial.readString());//Calls the parseData function to parse SMS
  }
  while (mySerial.available())
  {
    msg = mySerial.readString();//Forward what Software Serial received to Serial Port
  }

  if (msg.length() > 1) {
    start = msg.indexOf('*') + 1;
    endPoint = msg.indexOf('#') - 1;
    int count = 0;
    if (start > 1 && endPoint > 1) {
      strcpy( finalMsg, "");

      for (int i = start; i <= endPoint; i++) {
        finalMsg[count] = msg[i];
        count++;
      }
      Serial.println("SMS Received: ");
      Serial.println(finalMsg);
      LengMsg = count;
    }
    else{
      return false;
    }
  }
}

void updateSerial()
{
  delay(500);
  while (Serial.available())
  {
    mySerial.write(Serial.read());//Forward what Serial received to Software Serial Port
  }
  while (mySerial.available())
  {
    Serial.write(mySerial.read());//Forward what Software Serial received to Serial Port
  }
}

NB: The sms body should be between start and hash
Eg: * Hello Makers! #

codelery

@rafitc99 thank you so much. I will try it out and see if it will work.

codelery

This post is deleted!

codelery

@rafitc99 I tried this code, but the SMS is always corrupted. I got "Hello peopl⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮
"

instead of "Hello people of the village who work day and night to make sure all is well"

salmanfaris

@codelery Could you please share your code for checking?

codelery

@salmanfaris After countless trials and efforts without success, I have decided to use two separate microcontrollers (Atmega328p). One microcontroller receives SMS from SIM800l, parses it and sends it to the second microcontroller via serial interface (Arduino Rx and Tx pin). The second microcontroller receives the message via serial and send it to p10 module for display. This solution is not cost-effective because of the additional microcontroller. However, it solves the problem of interference between DMD library and SoftwareSerial which appeared to be the reason for the corrupted string I shared earlier.

However, I am facing another challenge; the message that the second microcontroller receives via serial interface is not complete. When I send "*Hello people of working with you are you doing tonight or tomorrow morning dear#" via SMS, what is received and displayed on p10 is "*Hello people of working with you are you doing tonight or tomo".

Here are the two codes:

Code for receiving SMS

 
 #include <SIM800L.h>
SIM800L sim800l(2, 3); //Rx, Tx
int LED_PIN = 8;

//Enter the phone number of the person whom you want to send sms
String reply = "Hey! I have got your message";

void handleSMS(String number, String message) {
  int start_index = message.indexOf('*'); // message starts with '*'
  int end_index = message.indexOf('#'); // message ends with '*'
  //message.trim();
  // if message starts with * and ends with #
  if(start_index == 0 && end_index == (message.length() - 1)) {
    Serial.println(message);
    blinkLed();
    sim800l.sendSMS(number, reply);
  } 
}

void setup() {
  Serial.begin(9600);
  pinMode(LED_PIN, OUTPUT);
  sim800l.begin(9600);
  sim800l.setSMSCallback(handleSMS);
}

void loop() {
  sim800l.listen();
}

void blinkLed(){
   for(int i = 0; i < 3; i++){
      digitalWrite(LED_PIN, HIGH);
      delay(1000);
      digitalWrite(LED_PIN, LOW);
      delay(1000);
 }
  }

*** Code for receiving and displaying message on p10 ***

#include <SPI.h>
#include  "buzzer.h"
#include <DMD.h>
#include "memory.h"

#include <TimerOne.h>

#include "SystemFont5x7.h"

#include "Arial_black_16.h"


#define ROW 3

#define COLUMN 1

#define FONT Arial_Black_16
char message [500] = "Welcome to electronic projects workshop 1234"; 
char r_msg[500] = "";
bool flag = false;

DMD led_module(ROW, COLUMN);


void scan_module()

{

  led_module.scanDisplayBySPI();

}


void setup()

{
  EEPROM.begin();
  Serial.begin(9600);
  buzzerSetup();
  beeps(3);

  int m_length = EEPROM.read(5);
 
    //    strcpy(message, "");
  String stored_string = read_string(5); 
     
  char stored_char[stored_string.length() + 1];
  stored_string.toCharArray(stored_char, stored_string.length() + 1); // convert message from string to array of char
  strcpy(message, stored_char); // update p10 with stored message

  Timer1.initialize(2000);

  Timer1.attachInterrupt(scan_module);

 led_module.clearScreen( true );
}

void loop()

{
  Serial.println(read_string(5)); 
    receiveMessage();
    
    led_module.selectFont(FONT);

    led_module.drawMarquee(message, strlen(message), (32 * ROW), 0);

    long start = millis();

    long timming = start;

    boolean flag = false;

    while (!flag)

    {

      if ((timming + 20) < millis()) 

      {

        flag = led_module.stepMarquee(-1, 0);

        timming = millis();
      }
    }

  }

void receiveMessage()
{
  /*
    Listens to incoming message through serial interface. 
    It extracts the message if it starts with '*' and ends with '#'
  */
  while(Serial.available())
  {
    String s_msg = Serial.readString();
    // s_msg.trim();
    int start_index = s_msg.indexOf('*') + 1;
    int end_index = s_msg.indexOf('#');
      
    // whether message contains * and # and also # comes after *
    if(start_index > 0 ){
        beeps(1);
        String substr = s_msg.substring(start_index, end_index - 1);
        int m_len = substr.length() + 1;
        char m_msg [m_len];
        substr.toCharArray(m_msg, m_len);
        
        strcpy(message, m_msg);
        // write to eeprom
        writeString(5, substr);
      }
   }
}

rafitc99

@codelery It might be because of buffer size of received message. You need to increase the buffer size.
Check the section "Expanding Arduino SoftwareSerial Buffer Size" in this tutorial : https://lastminuteengineers.com/sim800l-gsm-module-arduino-tutorial/

Help needed: Arduino Wireless Notice Board project

Recent Posts