Problem with power supply
Geethesh last edited by salmanfaris
The above image shows the ckt with ultrasonic sensor and attiny 45 Ic ,Bd 140 transistor (for switching the 6v pump).
***The problem is when I give power from 5v regulator to all this as shown in fig, the circuit is not working ,(not enough power ).
What should I do.
Should I give separate power to motor
I am using 5.5v adaptor 500mAh.
*I have checked the circuit by connection separate 5 v from arduino ,to that attiny 45 ic and sensor,. Then it is working .
- Please help
kowshik1729 last edited by kowshik1729
@Geethesh The problem is here. There is huge voltage drop at some point of the circuit(probably at the pump or sensor, you should find it by probing at those particular areas) such that the voltage is getting attenuated by the time it reaches the Attiny. So, Attiny is working only when a dedicated supply is given to it. You can try this out by having multimeter probed between the VCC and GND of the ATTiny45. Try having a stable supply to Attiny
Geethesh last edited by
Very much informative!!!!
If you are using raspberry pi as one of your main computers and have separate monitor, keyboard and mouse, then you might be tired of copy and pasting terminal commands and codes while doing projects with raspberry pi, because running chromium-browser and reading tutorial will pi slower and using a sperate keyboard and mouse use our workbench space too.
recently I read a blog Share your keyboard and mouse between computers with Barrier by Gordon Hollingworth which is cool.
In that blog, he mentioned a software called barrier, it's a software that will allow you to use a single keyboard and mouse to control multiple computers by physically turning a dial on the box to switch the machine you're controlling at any given moment. The barrier does this in software, allowing you to tell it which machine to control by moving your mouse to the edge of the screen, or by using a keypress to switch focus to a different system.
Follow these to share your computer keyboard and mouse with the raspberry pi
First, we need setup raspberry pi
Step 1: Download and Install Raspberry Pi OS on SD Card
Step 2: Connect raspberry pi to the wi-fi network
Step 3: Install barrier, for that open your terminal (Ctrl + T) and paste or enter the followingsudo apt install barrier
Then click enter.
Step 4: Setup barrier, Open barrier by typing barrier on the terminal, if you successfully installed the barrier you can see like this.
Select option Client (Use another computer's mouse and keyboard) and Select Auto config option too, also note the Screen name, which we need for the server.
That's all next we need to set up the desktop/laptop computer.
Step 5: Download and Install barrier on desktop or laptop computer (The Server), download link
Step 6: Set up the barrier by selecting Server and position your monitor on barrier software.
To Position, the screen clicks the configure server.
Here, to drag and drop the monitor icon to the desired position you need on the grid.
double click the screen and set the screen name, you can obtain the screen name from the raspberry pi barrier client. (See Step 4)
after setup, it should be like this. Then click OK
in the following screen, click Apply and Just wait few seconds then try to move the mouse to the corner. Yes, It should work.
@rafitc99 Looks cool, Thanks for sharing.
This is a speaker call for MakerChat by MakerGram. MakerChat is a webinar series where makers from different domain sharing their expertise with other fellow makers. MakerGram is an Open Community Platform for Makers and hardware enthusiasts to empower them by promoting learning, sharing and collaboration.
Do you think you can come up with some interesting ideas revolving around Amazon Alexa? What if we could help you build that idea into a reality. Tell us about your idea and the best one wins an Amazon Alexa Echo Dot.
🧲 Bonus points for those solutions involving Covid-19 or promoting social-distancing.
Schedule️Application - The application starts on 26th June 2020. Closing - The registration will end on 17th July 2020. Results - The results declared by last week of July
For Registration: https://alexa.hackclub.com/