MakerGram Logo

    MakerGram

    • Register
    • Login
    • Search
    • Categories
    • Recent
    • Popular
    • Tags
    • Users
    • Groups

    created PCB layout to control things using mobile with the help of arduino

    RSET PCB Designing Workshop
    3
    6
    666
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • kowshik1729
      kowshik1729 last edited by

      @Ggreeshma-stani Nailed the PCB in terms of the schematic. But you got it a little bad on the layout side. There are some thumb rules while designing a layout of PCB.

      1. Always place the oscillator and it's capacitors(C1, C2) near to the IC. If you have a doubt on this try checking the Arduino boards or any other boards. you will find an SMD chip crystal alongside of the Arduino XTAL pins. If you ask the reason for this that's simple, to avoid noise creeping in. Crystals provide the clock to the entire digital logic inside the IC. So, there should not be any noise in it. If noise is there, obviously you'll have timing issues.

      2. The bypass caps on the voltage regulator must be placed close to the regulator's input and output pins. The reason for this is also pretty simple, bypass caps will filter out noise coming from the power supply and few other reasons too. So, try placing these bypass caps as close as possible to IC.

      Apart from these points, the PCB looked good. Great work. Remember that this message is not to discourage you but just to give a suggestion so that you'll improve it in the next design.

      G 1 Reply Last reply Reply Quote 1
      • salmanfaris
        salmanfaris last edited by

        Thanks, @kowshik1729 Good suggestion, @Ggreeshma-stani consider suggestion mention above. 😊 👍

        also, try to minimize the board if you don't need that much size because PCB cost also depends on the board size too.

        G 1 Reply Last reply Reply Quote 1
        • G
          Ggreeshma stani @kowshik1729 last edited by

          @kowshik1729 sir i have made the appropriate corrections.
          and thank you for notifying me on the errors

          1 Reply Last reply Reply Quote 2
          • G
            Ggreeshma stani @salmanfaris last edited by

            @salmanfaris yes sir i have made the changes and have minimised the board size.

            1 Reply Last reply Reply Quote 2
            • kowshik1729
              kowshik1729 last edited by

              @Ggreeshma-stani Pretty good than the previous design. I am able to see 2 crystals on the board. Can I know why did you use another one?

              And finally, you can address me as kowshik. No need of sir😉

              1 Reply Last reply Reply Quote 0
              • First post
                Last post

              Recent Posts

              • @Ggreeshma-stani Pretty good than the previous design. I am able to see 2 crystals on the board. Can I know why did you use another one?

                And finally, you can address me as kowshik. No need of sir😉

                • read more
              • G

                @salmanfaris yes sir i have made the changes and have minimised the board size.

                • read more
              • G

                @kowshik1729 sir i have made the appropriate corrections.
                and thank you for notifying me on the errors

                • read more
              • @hisham Ahaaa...!! Looks like you've fixed the error. Great job.

                We'll be glad to have a look once your PCB is fabricated...😉

                • read more
              • @hisham also make sure Design Rules are matching with our manufacture capabilities! In this case, we are planned to use Seeed Studio Fusion PCB Service, so you can check their PCB capabilities and configure your PCB Design Rules.

                Fusion PCB Specification

                • read more
              By MakerGram | A XiStart Initiative | Built with ♥ NodeBB
              Copyright © 2023 MakerGram, All rights reserved.
              Privacy Policy | Terms & Conditions | Disclaimer | Code of Conduct